Table Place Name Assembly Instructions
The kit for each invitation consists of: Front Window Cutout Gears Cutout Base Cutout Holographic sticker Sheet of double sided foam pads You’ll also need a firm flat surface to work on and I suggest a ruler and tweezers would come in helpful.
You will need
1  Fix The Back Together
Turn over the Base Cutout Turn over the Base Cutout Remove the backing from the tape on the Gears Cutout Remove the backing from the tape on the Gears Cutout Turn over the Gears Cutout Turn over the Gears Cutout Carefully line up the Gears Cutout with the markings on the Base Cutout Carefully line up the Gears Cutout with the markings on the Base Cutout Press the joint firmly to ensure it sticks properly Press the joint firmly to ensure it sticks properly This is what it should look like so far This is what it should look like so far
2  Fix On The Sticker And Name Label
Peel off the sparkly label backing Peel off the sparkly label backing Line up the sparkly label with the markings on the Base Cutout Line up the sparkly label with the markings on the Base Cutout Smooth the label so it sticks properly Smooth the label so it sticks properly Peel the required printed name label from its backing Peel the required printed name label from its backing Carefully line the label up with the corner markings on the Base Cutout Carefully line the label up with the corner markings on the Base Cutout Check the label is in the right place before smoothing it down Check the label is in the right place before smoothing it down
3  Stick On The Front
Use tweezers to pick off the foam pads Use tweezers to pick off the foam pads Place a foam pad on each cross on the Base Cutout Place a foam pad on each cross on the Base Cutout Use the tweezers to peel the backing off each foam pad Use the tweezers to peel the backing off each foam pad Make sure the Front Cutout is facing the right way Make sure the Front Cutout is facing the right way Line up the corner of Front Cutout and lower onto the foam pad Line up the corner of Front Cutout and lower onto the foam pad Position the far end in place and lower it onto the foam pads Position the far end in place and lower it onto the foam pads Push the front down over the foasm pads to ensure it has stuck properly Push the front down over the foasm pads to ensure it has stuck properly
4  Fold The Base Together
Rest the place name face down on a table Rest the place name face down on a table Line up a ruler with the fold marks on the support Line up a ruler with the fold marks on the support Fold up the support Fold up the support Line the ruler up with the fold marks on the slotted tab Line the ruler up with the fold marks on the slotted tab Fold up the slotted tab Fold up the slotted tab Line the ruler up with the fold marks on the base Line the ruler up with the fold marks on the base Fold up the front of the place name Fold up the front of the place name Fold the support flat and fold the base flap further over Fold the support flat and fold the base flap further over Line the support up with the slotted tab Line the support up with the slotted tab Fold the slotted tab over so it locks into place Fold the slotted tab over so it locks into place Run your fingers along the fold to ensure its equal all the way along Run your fingers along the fold to ensure its equal all the way along The back of the place name should look like this The back of the place name should look like this Success! Success!
Table Place Name Assembly Instructions The kit for each invitation consists of: Front Window Cutout Gears Cutout Base Cutout Holographic sticker Sheet of double sided foam pads You’ll also need a firm flat surface to work on and I suggest a ruler and tweezers would come in helpful. 1  Fix The Back Together 2  Fix On The Sticker And Name Label 3  Stick On The Front 4  Fold The Base Together
Turn over the Base Cutout Turn over the Base Cutout
Remove the backing from the tape on the Gears Cutout Remove the backing from the tape on the Gears Cutout
Turn over the Gears Cutout Turn over the Gears Cutout
Carefully line up the Gears Cutout with the markings on the Base Cutout Carefully line up the Gears Cutout with the markings on the Base Cutout
Press the joint firmly to ensure it sticks properly Press the joint firmly to ensure it sticks properly
This is what it should look like so far This is what it should look like so far
Peel off the sparkly label backing Peel off the sparkly label backing
Line up the sparkly label with the markings on the Base Cutout Line up the sparkly label with the markings on the Base Cutout
Smooth the label so it sticks properly Smooth the label so it sticks properly
Peel the required printed name label from its backing Peel the required printed name label from its backing
Carefully line the label up with the corner markings on the Base Cutout Carefully line the label up with the corner markings on the Base Cutout
Check the label is in the right place before smoothing it down Check the label is in the right place before smoothing it down
Use tweezers to pick off the foam pads Use tweezers to pick off the foam pads
Place a foam pad on each cross on the Base Cutout Place a foam pad on each cross on the Base Cutout
Use the tweezers to peel the backing off each foam pad Use the tweezers to peel the backing off each foam pad
Make sure the Front Cutout is facing the right way Make sure the Front Cutout is facing the right way
Line up the corner of Front Cutout and lower onto the foam pad Line up the corner of Front Cutout and lower onto the foam pad
Position the far end in place and lower it onto the foam pads Position the far end in place and lower it onto the foam pads
Push the front down over the foasm pads to ensure it has stuck properly Push the front down over the foasm pads to ensure it has stuck properly
Rest the place name face down on a table Rest the place name face down on a table
Line up a ruler with the fold marks on the support Line up a ruler with the fold marks on the support
Fold up the support Fold up the support
Line the ruler up with the fold marks on the slotted tab Line the ruler up with the fold marks on the slotted tab
Fold up the slotted tab Fold up the slotted tab
Line the ruler up with the fold marks on the base Line the ruler up with the fold marks on the base
Fold up the front of the place name Fold up the front of the place name
Fold the support flat and fold the base flap further over Fold the support flat and fold the base flap further over
Line the support up with the slotted tab Line the support up with the slotted tab
Fold the slotted tab over so it locks into place Fold the slotted tab over so it locks into place
Run your fingers along the fold to ensure its equal all the way along Run your fingers along the fold to ensure its equal all the way along
The back of the place name should look like this The back of the place name should look like this
Success! Success!